Proven long-term UV resistance (5000h test acc. to EN 13859-2), validated by continuous testing
Suitable for open or ventilated cladding in timber, metal, stone and other materials, with open joints of up to 3cm
15-year product warranty for joint width of up to 3cm
Wind-tight, water-tight but vapour-open
Extremely lightweight, flexible and easy to install
Can be left uncovered for up to 4 months while retaining full performance warranty
BBA certificate 90/2548
Environmental Product Declaration can be downloaded here: https://www.dupont.co.uk/content/dam/dupont/amer/us/en/performance-building-solutions/public/documents/en/EPD-Tyvek-2524B.pdf
Drybase Liquid-Applied DPM is a single-pack barrier coating for above ground use. It is supplied ready to use. It is available in black or white with a consistency similar to that of thick emulsion paint. The product is applied in two coats. Drybase Liquid-Applied DPM Is suitable for use on solid floors, embedded timbers and walls. Once applied, the product cures to form a membrane that is flexible and elastic. Drybase Liquid-Applied DPM is water- based and can be applied to damp substrates by brush, roller, or spray. The applied product is typically touch-dry in one hour.
Size
1 Litre
Interior or Exterior Use
Interior
Coverage per Litre
4.5 m2 per 5 litres for vapour barrier, 7 – 9 m2 per 5 litres for general DPM
Fleece backed 100 mm waterproof butyl tape gives a well-bonded seal to the mesh face of Drybase. Plaster Membrane. The fleece backing to this tape also accepts a plaster coat finish as well as plaster adhesive where a dot and dab plasterboard system is preferred.
Sovereign Membrane Plugs are manufactured from glass filled polyamide, giving a high strength and corrosion resistant fixing. They are intended for use in damp proofing and waterproofing applications, to secure SovDrain membranes to the substrate, as part of the SovDrain waterproofing system. The plugs must be sealed using SovDrain Sealing Rope to the underside of the plug head in all below ground applications.
Sovereign CDM3 Lath/Mesh Membrane provides a robust drainage membrane suitable for use above and below ground on walls, floors and arched/vaulted ceilings, as part of the SovDrain waterproofing system. This membrane has a low stud profile (3mm), thus minimising wall and floor level changes.
Drybase Liquid-Applied DPM is a single-pack barrier coating for above ground use. It is supplied ready to use. It is available in black or white with a consistency similar to that of thick emulsion paint. The product is applied in two coats. Drybase Liquid-Applied DPM Is suitable for use on solid floors, embedded timbers and walls. Once applied, the product cures to form a membrane that is flexible and elastic. Drybase Liquid-Applied DPM is water- based and can be applied to damp substrates by brush, roller, or spray. The applied product is typically touch-dry in one hour.
Fleece backed 100 mm waterproof butyl tape gives a well-bonded seal to the mesh face of Drybase. Plaster Membrane. The fleece backing to this tape also accepts a plaster coat finish as well as plaster adhesive where a dot and dab plasterboard system is preferred.
Sovereign Membrane Plugs are manufactured from glass filled polyamide, giving a high strength and corrosion resistant fixing. They are intended for use in damp proofing and waterproofing applications, to secure SovDrain membranes to the substrate, as part of the SovDrain waterproofing system. The plugs must be sealed using SovDrain Sealing Rope to the underside of the plug head in all below ground applications.
Sovereign CDM3 Lath/Mesh Membrane provides a robust drainage membrane suitable for use above and below ground on walls, floors and arched/vaulted ceilings, as part of the SovDrain waterproofing system. This membrane has a low stud profile (3mm), thus minimising wall and floor level changes.